There's a lot you can do to make sure your time on a Yamaha WaveRunner is fun and that you're practicing safe habits. Replace the crankshaft bearings if out of specification. Steering sensor coupler black 5. Loose connection of bat- Check the battery lead and terminal tery terminal for proper connection. Improvisations and using improper tools can damage the equipment. The informa- tion has been compiled to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and inspection operations.
Operate the oil changer to extract the oil. Suspend the thermo sensor in a container filled with water, and then slowly heat the water. Therefore, do not turn the crankshaft after removing the camshafts. While retaining the stability and comfort of the F2X, the acceleration performance and maximum speed have been improved by increasing the output of the engine. Ribbon sub assembly bolt: 6. Pump out the engine oil with a commercially available Fluid Evacuator from the oil filler hole and drain pipe, to drain the oil tank and oil pan.
Trim switch coupler black 2. Compress the valve spring, and then install the valve cotter 1 using a thin screwdriver with a small amount of grease applied to it. Reface the valve seat with the valve seat cutter. All of the manual listed below are full factory service manuals with hundreds of pages containing step by step instructions, full wiring diagrams and detailed illustrations and photos on how to repair, rebuild or maintain virtually anything to your Yamaha Waverunner. Remove the dipstick and check the oil level.
Turn off the water and stop the engine. If the crankshaft-journal-to-crankshaft- journal-bearing clearance is out of speci- fication, select replacement crankshaft. Ignition coil malfunction Check the ignition spark. This entry was posted in and tagged , , on by. Fuel tank breather hose fuel tank to water separator 5.
So please make sure your email address is correct. Replace the Fuel hose assembly fuel pump module if out of specification. Lubricate: Crankshaft journal bearings with the recommended lubricant Recommended lubricant: Engine oil 2. Symptom 2 Cause Checking step page Yamaha Security System Check that the Yamaha Security 7-37 set to lock mode System is set to the unlock mode. Starter Motor Inspection Remove the safety lanyard switch from the engine stop switch. Engine oil level check 1.
Impeller housing 1 Bolt 6-11. This entry was posted in and tagged , , on by. Top ring side clearance b. Check the fuel hoses and hose connec- tions for fuel leakage. Internal: Drink large quantities of water or milk. Also, check that the clamp is installed on the oil tank securely. Clean around the spark plug bases with compressed air before removing the plugs, and be sure that no debris is allowed to enter the combustion chamber and remove the spark plugs.
Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat. Replace if out of specification. Top ring Oil ring b. When removing the fuel pump module, make sure that the rubber caps do not come off. Ribbon sub assembly bolt: 6. Remove the intake camshaft sprocket and exhaust camshaft sprocket.
Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Disconnect the ignition coil connectors. Remote start switch control receiver º. Is the ground line normal? This entry was posted in and tagged , , on by. Connect the steering cable joint to the ball joint, and then tighten the locknut to the specified torque.
Spark plug and ignition coil 2. . Re- place if cracked or damaged. Face the end of the plastic tie towards the sensor. Spray the lubricant into joint hole for 3 seconds.
Check that the throttle opens and automatically closes in all steering positions. Add the recommended engine oil up to the specified level through the oil filler hole. Fuel pump module and fuel sender 8. Replace the remote control transmitter battery if below specification. With step-by-step procedures combined with detailed photography and extensive use of exploded parts views, Clymer manuals are a must-have tool for the do-it-yourselfer. Remove the ignition coil for the cylinder Input voltage that will be tested. Warm up the engine with the watercraft in the water and check the idle speed.