Pro comp tach wiring. Autometer Basic Tach Installation Wiring Instructions Tutorial How 2019-01-26

Pro comp tach wiring Rating: 5,5/10 1883 reviews

How to Wire an Autometer Tach

pro comp tach wiring

If you like the design on our website, please do not hesitate to visit again and get inspiration from all the houses in the design of our web design. Make sure you have a good ground to engine and battery negative terminal. Limit one 1 rebate per household, per rebate period. Offer excludes truck freight and oversize fees. Go to for complete offer and redemption information. Special Note: Your model 2302 tachometer operates off your car's ignition.

Next

How to Install an Auto Meter Sport Comp 5in Tachometer w/ Shift Light on Your 1979

pro comp tach wiring

Wire installations should be neat and tied down to prevent tugging and fraying of wires at connections. Problems such as bouncing ignition points, bad plug wires, defective ignition capacitor, or arcing distributor cap may cause erratic readings on your tachomter. The following write-up is an overview of the installation I followed and includes a few illustrations from the installation guide provided from Autogage. Ignition manufacturers recommend that the ignition and coil be matched according to criteria which they establish often that the ignition and coil be products of the same company. Attach the base using screws provided or use a pop rivet tool.

Next

Pro Comp Tachometer Wiring

pro comp tach wiring

Connect the tach lead to that wire. Loosen both bolts holding the shock strap to the mounting foot. Offer excludes truck freight and oversize fees. See diagram in the wiring section. Register a Free 1 month Trial Account. Turn on the power to the tach.

Next

Reading : Pro Comp Tach Wiring Diagram 6811

pro comp tach wiring

Two-Stage Shift-Lite Set Mode For tachs with two shift-lite set points 1. This offer is a consumer rebate offer, dealers do not qualify. Valid on orders shipped in the contiguous United States. Connect the ring connector under the retaining bolt on the battery terminal and tighten the bolt with a wrench. The tach will now use the selected shift point, until set differently. A 12V motorcycle battery is a good alternative for cars without batteries.

Next

How to Install an Auto Meter Sport Comp 5in Tachometer w/ Shift Light on Your 1979

pro comp tach wiring

Stop when it reaches the desired shift point. If neither tach nor dial light work, check ground and 12V power connections. This offer is a consumer rebate offer, dealers do not qualify. A battery with minimum 5 amp hour rating is recommended. Most fuse boxes have several positions in the fuse box that will allow you to connect a wire to them using a spade connect. This is the indicator for High Set shift point. Note: These Instructions are for Auto Meter Gauges and Accessories only.

Next

Auto Meter Pro Comp Tach. Need Help Wiring!

pro comp tach wiring

Trouble Shooting If your tach does not function properly after installation check the following: 1. If the product you have is much older than these instructions, your product may not work exactly as described in the instruction. A Scotch lock should be used to lock up your whisky cabinet-lol. Limit one 1 rebate per household, per rebate period. This will minimize loose connections that could cause problems later.

Next

Pro Comp Tach Wiring Diagram Magneto

pro comp tach wiring

Turn the ignition on and the shift point setting will show on the dial. Offer excludes truck freight and oversize fees. Are all electrical connections correct and tight? Plug is directional, do not force fit! To accomplish changing the shift setting, a Blue lead is brought out of the tachometer to a switch that the driver may manually push. Truck freight and oversize charges still apply unless otherwise notes and can only be shipped to the lower 48 States. When the switch is closed pushed , the Blue lead will be connected to 12V Power and the Low Set mode will be in effect.

Next

How to Install an Auto Meter Sport Comp 5in Tachometer w/ Shift Light on Your 1979

pro comp tach wiring

To double check, push red set button-- pointer will indicate your shift-point. A Scotch lock should be used to lock up your whisky cabinet-lol. When shifted out of 1st Low , the switch returns to open and places the shift point in the High Set mode. Go to for complete offer and redemption information. Valid on orders shipped in the contiguous United States. Valid on orders shipped in the contiguous United States. On my 240 I used a piggy-back connector onto the instrument light rheostat.

Next

Autometer Pro Comp Tach Wiring Diagram Free Download • Oasis

pro comp tach wiring

Run the red wire from the back of the tachometer to the fuse box of your car. The instructions on this page are the most current version of each instruction. Go to for complete offer and redemption information. Prior to installation of your tachometer, check with the ignition box manufacturer for recommended tachometer signal location. This offer is a consumer rebate offer, dealers do not qualify. Valid on orders shipped in the contiguous United States.

Next