Put a Handset in Every Room With four handsets one base and three chargers and the option of adding up to two additional handsets — all while using only one base and one phone jack — go ahead and put one in the den, the kitchen, the master bedroom and the living room so you won't have to make a run for it when the phone rings. Accessories and Packing Materials 16. Base Unit Reference Drawing When connecting the simulator equipment for checking, please refer to below. If you can not proceed to the next step, refer to Registering a Handset to a Base Unit P. Handset Reference Drawing When connecting the simulator equipment for checking, please refer to below. So turn off the ringer and never miss a call. Check Handset Transmission Cross Reference: Signal Route P.
Transmitting and receiving carrier between base unit and handset is same fre- quency. Register a Free 1 month Trial Account. How to Clear User Setting Units are reset to the Factory settings by this operation Erase recorded Voice messages, stored Phone numbers, Caller list and etc. Refer to Frequency Table P. Adjustment and Test Mode Flow Chart 8. Please check the manufac- turer's specific instructions for the melting points of their products and any precautions for using their product with other materi- als. © 2008 Panasonic Communications Co.
Circuit Board Charger Unit --------------------------- 98 2 Warning -------------------------------------------------------------- 4 15 Appendix Information of Schematic Diagram --------- 99 2. Before going to sleep, simply set the bedside handset to Night Mode so that it won't ring in your bedroom. For Service Technicians --------------------------------- 4 14. . Panasonic Dect 60 Manual Kx Tg9341t can be very useful guide, and panasonic dect 60 manual kx tg9341t play an important role in your products.
Check Playback Cross Reference: Note: Power Supply Circuit P. Unauthorized copying and distribu- tion is a violation of law. The Light-Up Indicator with Ringer Alert at the base of the antenna will flash quickly to show that you have an incoming call, and it will flash slowly to let you know you have a new message. It also assures greater protection against eavesdropping for all your calls. Replacement Parts List Safety Ref.
Main charge 180~250 mA at the Battery of maximum 7- hours is started soon after the handset is placed on the charger unit. Never Miss a Call with the Light-Up Indicator Don't miss important calls when the ringer is off. Check Power Cross Reference: Note: Power Supply Circuit P. Hot air disordering tool , conduct the following operations. Circuit Board Charger Unit 14. The schematic diagrams may be modified at any time with the development of new technology.
Registering a Handset to a Base Unit 10. The Phone That Talks Now you don't have to be holding the phone to see who's calling. Programming by Scrolling through the Display Menus. Check and Adjust Frequency Base Unit 1. After the information is stored, those unwanted callers will receive a busy signal when they call you again.
Deregistering All Handsets by the Base Unit. Adjustment Mode for Base Unit Cross Reference Check and Adjust Frequency Base Unit P. Finding out the Defective part After All the Checkings or Repairing 1. The host processor provides activation and control of all that func- tions as follows. Suggested PbF Solder There are several types of PbF solder available commercially.
Power Supply Circuit Voltage is supplied separately to each block. Parallel Connection Detect Circuit Function: In order to disable call waiting and stutter tone functions when using telephones connected in parallel, it is necessary to have a circuit that judges whether a telephone connected in parallel is in use or not. Acoustic Testing Mode Notes: 1. Please refer to the each item. While this product is manufactured using Tin, Silver, and Copper Sn+Ag+Cu , you can also use Tin and Copper Sn+Cu , or Tin, Zinc, and Bismuth Sn+Zn+Bi. In that case, by recharging the battery as mentioned above, you will get a correct indication of the battery strength. In the meantime, the handset in the den will still ring when that important call comes in without disturbing the person who's sleeping.
Programming using the Direct Commands. Check Handset Reception Cross Reference: Signal Route P. Then it changes to Trickle charge to prevent from over- charging. This operation should not be performed for a usual repair. Troubleshooting Flowchart Cross Reference: Note: Check Power P.
The problem is that once you have gotten your nifty new product, the panasonic dect 60 manual kx tg9341t gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Night Mode Lets You Choose Where the Phone Rings Now you can program each handset to ring — or not — at your discretion. . . . . .