To add a device, press Menu once so that the C10 returns to the System screen. Stroke remains the same at 75. It has a valvetrain design. If you are only setting up the C10 for a single engine, you do not need to make any changes on this screen. Posted on Jun 10, 2011 asked hundreds of times an answered the engine is a suzuki G10 they are no solid lifters.
Ensure that the stud holes are cleaned out with a thread tap and there is no water or oil at the bottom of the hole. Jun 04, 2014 98 and older suzuki swift torque is 54 ft. The mounting points of the engine block were similar to that of the G13 and so an engine swap was a relatively easy task. It was phased out when production of Zen ceased in 2006. Maximum Seating: 4 Performance Data Performance Base Number of Cylinders: 4 Base Engine Size: 1. Select Fuel Remaining and press Enter. Since it does not need to be configured, go to the next step.
It shares the G15's 75 mm 2. As the only market in the world, Canada did continue to receive this engine for its versions of the second generation Cultus. It is Euro-4 emissions compliant. Select Network and press Enter. Produced by Suzuki Motor of America, Inc. If you work on your owner need to provide your mechanic with additional information then this is the compilation for you. Tons of pictures and diagrams at your fingertips!! Use the arrow buttons to select System and press Enter.
There are three selections within the Fluid Level Sensor screen: — Configure — Alarms — Calibrate 3. The screen returns to the Network screen — press Enter again. There is no need to Configure the engine interface for a single-engine installation. All G13 engines have a bore and a stroke size of 74 mm × 75. Archived from on May 26, 2006. Use the arrow buttons to specify Tank size.
Your email address will not be published. These are the same for manuals given to official dealer's workshops, they contain detailed instructions and step by step diagrams for all workshop procedures everything from changing the plugs to rebuilding the engine, as well as electrical diagrams, torque settings, fluid capacities,www. The default setting for Alarms is zero, but it is recommended that a low fuel alarm be set. Then select Set Configuration and press Enter. On the Settings screen, select Pages, then press Enter. Use the arrow buttons to select Alarms, then press Enter. Interior Front Head Room: 37.
Wiring service suzuki g10 engine diagram also with chevrolet monte carlo Suzuki G10 Engine Diagram Comments and Responses on Wiring diagrams, engine problems, fuse box, electrical diagram, transmission diagram, radiator diagram, exhaust system, suspension diagram. A warning screen asks you confirm that you want to change the fluid level configuration — select Yes and press Enter. This engine was made with different valvetrain designs: 8 or 16 valve or 16 valve. After pressing Enter, the Pages screen shows a check mark and a description for the page you have just selected for item number 4 on the list. Wiring color code or symbols, wiring harness, radio and audio wiring, circuit diagram, light switch wiring diagram. The detail level within the manual is excellent, in typical fashion.
Press Enter to select Settings. Then select Settings and press Enter. Select Replace and press Enter — this allows you to choose from ten custom page templates. Select Device List and press Enter. Use the down arrow to select Fluid Type, then press Enter.
From 1989 to 2001 the engine received updates in the form of and. If you see live data, this confirms that the device is both connected properly and is transmitting data to the C10. Press Menu to return to the default screen. This engine has a valvetrain design. Redline is set at 7400-7600 rpm. To start, select from the Num Pts drop-down and select Calibrate. Suzuki G10 Engine Diagram Service This amazing suzuki g10 engine diagram that offers along 3 pictures including suzuki 3 cylinder engine additionally suzuki swift engine moreover suzuki samurai engine together with suzuki 3 cylinder motorcycle engine also with suzuki g10 engine specs including suzuki motor including suzuki swift gti also with geo metro 1.
Use the arrow buttons to adjust the alarm percentage for example, 20 percent. When the Fluid Level - Calibration screen re-opens, select Full from the Fluid level drop- down, then select Calibrate and press Enter. Tons of pictures and diagrams at your fingertips!! To set the time and date manually, use the arrow buttons to select Time format, then use the arrow buttons to select the 12-hour or 24-hour time format and press Enter. Indomobil Suzuki International Service Department, November 1993, p. Select box number 4 and press Enter.
This engine has an valvetrain design, making periodic timing belt changes vital to the engine's life. If you are only setting up the C10 for a single fuel tank, use the arrow buttons to select Total Fuel Capacity. There was also a variant built in Indonesia which combines the longer stroke with a 75 mm 2. Use the arrow buttons to select Fluid level sensor. Press the Menu button and select save, then press Enter. The Device List screen that opens is used to access and configure each device connected to the network. This includes: 1 C10 Color Display.