Konica 7022 service manual. Konica 7022 2019-01-28

Konica 7022 service manual Rating: 6,6/10 813 reviews

Konica 7022

konica 7022 service manual

The following indicators are used on the caution labels or in this manual to categorize the level of safety cautions. After completion of printing, the copier will automatically return to the List Print Screen. Zoom ratios can be selected from 25% ~ 400% in 1% increments. The default password of 0000 allows the timer function to be interrupted without the requirement for password entry. Auto Reset Automatically resets to auto mode defaults after a specified period of copier inactivity. The loaded paper size will be indicated on the bypass tray key of the Basic Screen. Select the desired darker exposure from the sample sheet s , then touch the density number from 1 to 16.

Next

Konica 7115/7118 Printer Service Repair Workshop Manual

konica 7022 service manual

These materials may cause poor image quality. The time period for the Automatic Shut-Off function can be set for 1 minute, 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes or 240 minutes. The application function keys currently set are displayed on the screen. The scanned image will be printed on the specified paper size using an automatically selected magnification ratio. Similarly, 2-1 Flip Side 2 rearranges the reverse side of duplex originals which reads upside down to make normal simplex copies. Use only a power source with the correct rating for the machine; otherwise, hazardous situations such as smoking or overheating may occur.

Next

Konica 7022

konica 7022 service manual

If you change the place of installation, please contact your service representative. All scanned data will be erased. If the breaker trips or the fuse blows, turn off the power switch, reset the breaker or the fuse, and turn on the machine. Working Day Individual Setting Screen W. The Basic Screen will be displayed. The machine will output the scanned data for job completion in the amount remaining in the print quantity setting. Your service representative will contact you to determine the appropriate means for resolving the problem.

Next

Konica 7020 7022 7025 Workshop Service Repair Manual

konica 7022 service manual

However, copying can be available by using the following procedure. When copying is completed, close the Multi-sheet bypass tray. Be sure to insert the rear guide plate into the position of the paper size to be set; otherwise machine trouble may occur. While pressing the release knob, move the side guide plate against the paper. Lock Job Memory Paper Type The following functions can be provided by the Memory switch settings. The quantity displayed on the touch panel will return to 1.

Next

Konica 7115/7118 Printer Service Repair Workshop Manual

konica 7022 service manual

To the depth To the left Copying OperationsPositioning Originals Setting Print Quantity Paper Size 3 Setting direction Lens Mode Density Reminder! The machine can be set to stop immediately or after a job is completed, or to only display a warning message. Auto Low PowerThis function conserves energy by lowering the set temperature of the fixing unit. Conditions required to use the Weekly Timer: The power plug is inserted into the socket. The time setting area will appear grayed out and cannot be selected. Load transparency film one sheet at a time. Select additional copy conditions, as desired.

Next

Konica 7022 service manuals

konica 7022 service manual

Once closed, do not open the document feeder, otherwise the selected copy conditions may be altered automatically. Stack paper with curl side up. The Weekly Timer is a copier management function that shuts down power to the machine on a daily or hourly basis, and can be programmed specifically for lunch breaks, weekends and holidays, or any time the copier is not required. Booklet Creates A4R or A4 size booklets from A4 size originals in 1a2 or 2a2 copy mode. Dual Page Copies both pages of an open book or book-size sheet separately onto two A4 sheets in 1a1 mode or separately onto each side of one A4 sheet in 1a2 mode. Do not attempt to repair it yourself, and do not continue to operate the copier. Load paper, aligning it to the right side of the tray.

Next

Konica 7020 7022 7025 Workshop Service Repair Manual

konica 7022 service manual

This operation can be completed normally without the name specified. When Staple mode is selected, this icon indicates the number of staples and staple position. Copier Initial to display the Copier Initial Setting Menu Screen, then touch 3. If the inserted power plug is loose in the socket, even after it has been positively inserted, disconnect the plug and contact your electrical contractor. The default setting is collective: On for Mondays through Saturdays, and Off for Sundays.

Next

Konica 7115/7118 Printer Service Repair Workshop Manual

konica 7022 service manual

Preset Key Setting Menu Screen Userset Density Selection Screen Key Operator Mode System Initial Copier Initial Preset Key E. Be careful when withdrawing the fixing unit. Lock Job Memory Tray Initial Setting Screen Paper Type Panel Contrast Key Operator Data Weekly Timer Touch Panel Adjustment Power Save Memory Switch Procedure1 Touch 2. The Name Input Screen will be displayed. Do not throw the empty toner cartridge into a fire. Lock Job Memory Paper Type Panel Contrast Key Operator Data Procedure1 Touch 2.

Next

Konica 7115/7118 Printer Service Repair Workshop Manual

konica 7022 service manual

Automatic Duplex CopyingTo reduce paper consumption, use this function to make double-sided duplex copies, automatically. Check pages of the output set to confirm the amount of missing data, then complete the job according to the print quantity remaining. Userset Density Darker Setting Screen Lock Job Memory Paper Type Panel Contrast Key Operator Data Weekly Timer Touch Panel Adjustment Power Save Memory Switch List Print Application Customize Density Shift Touch No. The main power switch does not have to be turned off. Once deleted, the programs cannot be restored. Auto Low Power Automatically lowers the power after a specified period of copier inactivity. The settings of a locked job cannot be changed.

Next