Kawasaki ninja zx 10r 2006 2007 service manual. Kawasaki ZX10R 2006 2007 Workshop Service Repair Manual 2019-01-28

Kawasaki ninja zx 10r 2006 2007 service manual Rating: 6,2/10 1829 reviews

Kawasaki Ninja ZX

kawasaki ninja zx 10r 2006 2007 service manual

Clamp Hold the brake pipe. Fuel Pressure with Engine Idling Standard: 294 kPa 3. Face the hook portion of the bracket to inside of the vehicle. All diagnostic and repair procedures are covered in great detail. Main Fuse 30 A 10.

Next

2006

kawasaki ninja zx 10r 2006 2007 service manual

One way to install inserts is as follows. If the engine does not stop, inspect the engine stop switch see Switch Inspection in the Electrical System chapter. Run the red hose return to outside of the white hose vacuum. Ignition Fuse 15 A 7. Immobilizer Amplifier Equipped Models 12. Hold the brake hose with the bracket.

Next

Kawasaki Service Repair Manual Download

kawasaki ninja zx 10r 2006 2007 service manual

Run the fuse box 1 lead in front of the fuse box 1. Set it close to the bottom of the cylinder, where cylinder wear is low. Wheel Balance 10 g 0. Clamp Hold the air intake solenoid valve lead equipped models. Oxygen Sensor Heater Equipped Models : R 77.

Next

2006

kawasaki ninja zx 10r 2006 2007 service manual

Clamp Hold the front brake hose and the front wheel rotation sensor lead at the white painted position of the lead. Run the lead to outside of the hose. Tons of pictures and diagrams at your fingertips!! Clamp Hold the front brake hose and the front wheel rotation sensor lead at the white painted position of the lead. Torque - Shift Shaft Return Spring Pin: 29 N·m 3. If any journal has worn past the service limit, replace the crankshaft with a new one. If quick charge is done unavoidably, do standard charge later on.

Next

2006

kawasaki ninja zx 10r 2006 2007 service manual

Torque - Bleed Valves: 7. The manual covers the complete tear down and rebuild, pictures and part diagrams, torque specifications, maintenance, troubleshooting, etc. Replace the chain guide if it shows any signs of abnormal wear or damage. Insert the tab into the slot. Lubri- cation points are called out throughout this manual, apply the specific oil or grease as specified.

Next

2002

kawasaki ninja zx 10r 2006 2007 service manual

Never remove the seal cap during refresh charge. Run the throttle sensor leads leftward. To facilitate actual operations, notes, illustra- tions, photographs, cautions, and detailed descriptions have been included in each chapter wherever necessary. Learn and ob- serve all the rules below. Oxygen Sensor Lead Equipped Models 5.

Next

2002

kawasaki ninja zx 10r 2006 2007 service manual

If any wiring is poor, replace the damaged wiring. Coolant Reserve Tank Overflow Hose 7. Seat Height 813 mm 32. If meter does not work, replace the meter unit. Overall Height 1 115 mm 43. Right Switch Housing Lead 8.

Next

KAWASAKI NINJA ZX

kawasaki ninja zx 10r 2006 2007 service manual

Replace any defective parts, if necessary. Clamp Hold the damper of the front wheel rotation sensor lead. Check the oil level before each use and change the oil and filter according to the periodic maintenance chart. Run the fuse box 2 lead in front of the rib for the fuse box 2. Run the right switch housing lead above the main harness. Run the fuse box 2 lead in front of the rib for the fuse box 2.

Next

2006

kawasaki ninja zx 10r 2006 2007 service manual

Such a shock to the sensor can damage it. Terminal Voltage: 12 V or lower Charging Method: 0. If they appear damaged or deteriorated, replace them. Align the white marks with the projections of the fitting. Face the stopper upward, and install the clamp under the frame ground terminal.

Next