If necessary, set up lighting at the work site. If the ground collapses, the machine could fall or tip over resulting in serious injury or death. Remove any dirt from the window glass, mirrors, handrails, and steps. It has tons of pictures and diagrams at your fingertips. The bucket does not have to make physical contact with power lines for current to be transmitted. Check gauges and monitor displays for normal operation before starting the engine. There is a danger that this may lead to a serious accident.
Vibration or unusual noise during operation could be an indication of air leaking into the circuit Refer to the appropriate Troubleshooting section for component or unit for procedures. Use paint marks at the same point on the swing body and undercarriage, or select alternate measuring locations and use a stopwatch to time 3 full 360° rotations. You can do it at the comfort of your garage. Prevention of Crushing and Cutting You should always have at least two people working together if the engine must be run during service. Unless you are instructed otherwise, never attempt adjustments while the machine is moving or while the engine is running. See the Shop Manual for information on partial disassembly. Vibration, irregular or difficult movement or unusual noise from any part of the hydraulic system could be an indication of air in the system and many other types of problems.
Some actions involved in operation and maintenance of the machine can cause a serious accident, if they are not done in a manner described in this manual. Wherever it appears in this manual or on safety signs on the machine you must be alert to the potential for personal injury or accidents. It will help you fix every part of it. No shipping fee, No waiting nervously for the postal delivery, you can start doing your repairs right away! Kind of tough to do that with a paper manual. It has tons of pictures and diagrams at your fingertips.
Do not smoke while you are checking the battery's electrolyte levels. Investigate the configuration and ground conditions of the work site beforehand to prevent the machine from falling and to prevent the ground, stockpiles, or banks from collapsing. Accumulator The pilot control system is equipped with an accumulator. You will get workshop repair service manual right away in your email after you pay. It is recommended that an appropriately sized 2. Improper lifting can allow load to shift and cause injury or damage.
Follow all safety recommendations and safe shop practices outlined in the front of this manual or those contained within this section. It can save your expenses. Never weld when the engine is running. If the machine has to be used on a slope, pile the soil to make a platform that will keep the machine as horizontal as possible. If you ever lose your service manual just contact us we will send to you the service manual within 24 hours for free for lifetime. However, pressure loss could also be because of cavitation or air leakage, or other faults in the hydraulic system. It may also be used to alert against equipment that may detonate or explode if handled or treated carelessly.
If you ever lose your service manual just contact us we will send to you the service manual within 24 hours for free for lifetime. It is the manual used in the local service repair shop. Traveling on slopes could result in the machine tipping over or slipping. You will get workshop repair service manual right away in your email after you pay. Register a Free 1 month Trial Account.
Never hold any control levers when getting on or off the machine. Booster or charger cable connections must be made between the nonseries connected positive terminals and between the negative terminal of the booster battery and the metal frame of the machine being boosted or charged. The safety information on the following pages is organized into the following sections: 1. Broken down on the trail or site and have a smart phone? Do not swing the work equipment from the uphill side to the downhill side when the bucket is loaded. If inspection and maintenance are carried out when the machine is dirty, it will become more difficult to locate the problems, and there is a danger that you may get dirt or mud in your eyes or that you may slip and injure yourself. Battery cables must be disconnected before the welding procedure is started.
This prevents dirt from getting into the machine and ensures safety during maintenance. Make sure that all other work site crew members are kept well away from the excavator and safe from possible hazards. No shipping fee, No waiting nervously for the postal delivery, you can start doing your repairs right away! If there is any question about whether your machine and work site complies with the applicable standards and regulations contact your local authorities and agencies. If maintenance work is carried out with the inspection cover open but not locked, there is a danger that it may suddenly close and cause injury if there is a gust of wind. Lower everything to the ground before leaving the operator's seat. Make sure the ground surface is as hard and horizontal as possible before carrying out operations. Warming up the engine for a short period may be necessary, to avoid operating with sluggish or reduced working capacity.