Bose cinemate service manual. Bose CineMate 130 manual 2019-01-26

Bose cinemate service manual Rating: 4,1/10 777 reviews

BOSE LIFESTYLE

bose cinemate service manual

The commands should have at least 100msec spacing between them. Perform the following to gain access to the tuner adjustments. Verify that the disc plays properly. Might make a good Christmas present for one of my kids. The next three digits are the Julian date for the day of the year.

Next

BOSE LIFESTYLE

bose cinemate service manual

The region code can be changed an additional three 3 times after this before the setting becomes permanent in the drive and no more changes are permitted. I have searched for a schematic but I haven't had any luck. Optical Digital Audio Test 1. It should read -25 dB or less. It should be 470 mVrms + 10%. Refer to the table below for a list of responses. The output should be 0 dB, +0.

Next

Bose® CineMate® GS Series II

bose cinemate service manual

There is only one version of the bass module. Play tracks 1 through 15, verifying that each track cues up within the test limits. We went through a short troubleshooting routine and at the end gave me three options. Find all the documentation for downloading your vintage hifi or audiophile Bose on vintageshifi. Press the grille in place.

Next

BOSE LIFESTYLE

bose cinemate service manual

Replace any array with an extraneous noise that can be heard at a distance greater than 1 foot 0. Lift the top edge of the outer bezel assembly away from the console slightly. Press the volume up + button on the console for 10 seconds to put it at full volume. Gemstone Satellite Array Procedures 1. Verify that the disc plays properly. Do this for both the composite and S-Video outputs on the media center. For Bose contact information, refer to the address sheet included in the carton.

Next

CineMate® 1 SR home theater speaker system

bose cinemate service manual

If not, it is wired incorrectly. The examples shown on the following pages are for Hyperterminal as used with Windows® 2000 Professional. If it is not within the limits specified, there is the possibility of a shock hazard, and the unit must be repaired and rechecked before it is returned to the customer. Refer to the photos at right for the following procedures. You could suffer a fatal electrical shock! All the downloadable content on this website has been scanned thoroughly for viruses. Vibration can cause the speaker to move, particularly on smooth surfaces like marble, glass, or highly polished wood.

Next

Bose Cinemate 10 Repair

bose cinemate service manual

Track - Individual selections recorded on an audio tape or disc. Notify Bose or your authorized Bose dealer immediately. If the rubbing can be made to go away or get worse, then it is a rub or tick. Instead, contact your nearest service center! This part is referenced for informational purposes only. This will tune the unit to the appropriate frequency. Use only replacement parts that have critical characteristics recommended by the manufacturer.

Next

Free Bose Diagrams, Schematics, Service Manuals :: Schematics Unlimited

bose cinemate service manual

Re-assembly Note: When connecting the ribbon cable to the new hard drive assembly, take care that the red stripe aligns with pin 1 of the connector. Most high-end televisions have S-video inputs. Press the volume up + button on the console for 10 seconds to put it at full volume. Verify that the level is greater than 40 mVrms. Refer to the photo at right for an image of the converter.

Next

Bose Cinemate 10 Repair

bose cinemate service manual

Verify that the track plays properly. Your dialog box views may vary slightly depending on the version of Windows and Hyperterminal you have. The following is an example: Serial No. On inspection, the Cinemate 10 and Cinemate 15 appear to be nearly identical; however, the differences between the models are their prices and remote control styles. They are the Zone 1 and Zone 2 audio inputs for the console. A complete manual for the device Bose CineMate 130, how should it look like? If I can fix it for less, it will be a better deal.

Next

Cinemate GSII Service Manual

bose cinemate service manual

Reference a dB meter to the signal generator output signal. Insulation Resistance Test Cold Check- 1 Unplug the power supply and connect a jumper wire between the two prongs of the plug. Set the properties in the dialog box as shown at right. Verify that the video appears on the video monitor. Other commands require the technician to make measurements and adjustments. Set up the unit under test as shown in Figure 1 for the following tests. Use the following checks to perform these measurements: A.

Next

Bose Cinemate 10 Repair

bose cinemate service manual

Note: The system must have power removed, and then re-applied in order for it to boot. If you do not perform a flash update, the console will revert to the previous settings when power is removed. Refer to the next higher assembly for a replacement part. The two systems are fairly identical in regards to sound quality. Once completed, be sure to delete the disc from the console. All Bose products must be used in accordance with local, state, federal, and industry regulations. Unpowered Transformer Impedance Test 1.

Next