Measure the resistance of the Ambient Temperature Sensor. Is the voltage above 4. Disconnect the Airbag Control Module connector s. Reconnect all previously disconnected components. Disconnect each front and rear speaker harness connector. Disconnect the Rear Blower Rear Control Switch C1 harness connector.
Set Condition: When voltage is below 4. Operate the right power sliding door with either the key fob or the overhead console. Disconnect the Fuel Tank Module harness connector. Disconnect the Body Control Module C2 harness connector. Is the resistance above 100k ohms? Disconnect the Sliding Door Control Module C2 connector.
Turn the park lamps on. Disconnect the License Lamp light bar connector. While back probing, measure the voltage of the Front Intrusion Sensor Signal circuit at the Thatcham Alarm Module 16-way connector. This is an excellent opportunity to avoid a major fault arising out of a minor one. Measure the voltage between Seat Sensor 5 volt supply circuit and ground. Disconnect the Message Center harness connector.
Disconnect the Body Control Module C5 harness connector. Measure the resistance between the Recirculation Door Driver A and B circuits. Disconnect the Airbag Control Module connector s. Repair Replace the Body Control Module. Disconnect the Seat Airbag connector. Disconnect the Rear Blower Motor Power Module C1 harness connector. As a whole, Chrysler has come to represent a certain quality, a ruggedness that is present in the best American cars, linked to an element of style and excellence However, it goes without saying that a car will only take so much heavy use before it develops faults.
Set Condition: The Full Open Switch was detected as closed before 100 hall effect pulses were counted since the start of the close operation. A repair manual comes with comprehensive details regarding technical data, diagrams, a complete list of car parts and pictures. Does the test light illuminate brightly? Measure the resistance between the Evaporator Temperature Sensor Signal circuit and the Rear Blower Motor Control circuit. Does the blend door move smoothly in both directions? Disconnect the Automatic Temperature Control Module C2 harness connector. Set Condition: The radio has sensed a short on the output for more than 10 seconds.
Wiggle the harness and check for an intermittent short circuit condition. Measure the voltage of the Seat Horizontal Rearward Switch Sense circuit to ground. Disconnect the Rear Blower Motor Power Module C2 harness connector. Set Condition: When output voltage status is Low. Operate the power sliding door several times if possible.
Using the schematics as a guide, inspect the wiring and connectors specific to this circuit. Disconnect the Body Control Module C3 connector. Disconnect the Sliding Door Latch Sensing Switch connector latch assembly. Disconnect the Driver Power Seat Front Riser Position Sensor Connector. Measure the resistance between the Blower Motor Low Driver circuit and the M1, M2, M3 and Blower Motor High Driver circuits. Set Condition: If the seat switch is active for 30 seconds, this code will set and the Memory Seat Mirror Module will ignore the input until the state has changed. Read more: The Chrysler Voyager remains to be one of the most handsome minivans extant, nevertheless of the trim stage.
Measure the voltage between Seat Sensor 5 volt supply circuit and ground. For 2003, there is small to distinguish several-cylinder models from V6 models as all of them use coloration-keyed cut throughout. When a trouble code occurs, the airbag warning indicator illuminates for 12 seconds 3. Using a 12-volt test light connected to ground, check the Park Lamp Output circuit. Make sure that the Rear Blower Motor Relay is installed. For all the know-how needed to care for and repair your vehicle, our Chrysler Voyager 2003-2007 repair manual will guide you every step of the way.
Disconnect the Rear Blower Front Control Switch harness connector. Operate the blower motor in all speeds. Turn the ignition on while observing the voltmeter. Disconnect the Load Tool from the Passenger Airbag connector s. Turn all lights and accessories off. If not, refer to the symptom list from the menu and repair as necessary.
Disconnect the Airbag Control Module connector s. Using a 12-volt test light connected to 12-volts, check the Ground circuit. Is the resistance below 10000. Measure the resistance between ground and the Radio Dimming circuit. Repair Replace the Memory Seat Mirror Module.